Rifle Zero Calculator

Your load and zero

Factory-equivalent examples are starting points, not measured data for your rifle. Edit velocity and BC to match your ammunition.

Atmosphere · 59°F · 29.92 inHg · 0% humidity

Use station pressure, not sea-level pressure. Convert a weather-app value with the density altitude calculator.

Impact at 25 yd
0.8 in low

Where to hit at 25 yd for a 100 yd zero

Zero distance
100yd

Where the bullet crosses your line of sight

Far zero
—

No other crossing between 10 and 500 yd

Point of impact with a 100 yd zero

RangeImpact vs aimMOAMILVelocity
10 yd1.4 in low12.9 ↑3.76 ↑2696 fps
25 yd0.8 in low3.2 ↑0.94 ↑2674 fps
50 yd0.3 in low0.5 ↑0.14 ↑2638 fps
100 yd0.0 in0.0 ↑0.00 ↑2567 fps
150 yd1.1 in low0.7 ↑0.20 ↑2497 fps
200 yd3.5 in low1.7 ↑0.49 ↑2429 fps
250 yd7.5 in low2.9 ↑0.83 ↑2361 fps
300 yd13.0 in low4.1 ↑1.20 ↑2294 fps
400 yd29.0 in low6.9 ↑2.01 ↑2165 fps
500 yd52.5 in low10.0 ↑2.91 ↑2039 fps

Arrows show which way to dial or hold to hit point of aim. Level shot, no wind.

Take this solver to the range — works 100% offline

Save your rifles and loads once, pull live weather or pair a Kestrel, and get instant elevation and wind holds with zero cell service.

Download the App

Free on iPhone and Android. Your website inputs are not automatically imported into the app.

25-Yard & 50-Yard Short-Range Sight-In Chart

Where your group should print on a 25-yard or 50-yard indoor/short range to be zeroed at 36, 50, 100, or 200 yards with this load, plus where the bullet crosses your line of sight again.

Target ZeroHit at 25 ydHit at 50 ydHit at 100 ydHit at 200 ydSecond ZeroAction
25 yd zero0.0 in1.4 in high3.4 in high3.3 in high≈ 263 yd
36 yd zero0.5 in low0.5 in high1.5 in high0.5 in low≈ 186 yd
50 yd zero0.7 in low0.0 in0.5 in high2.5 in low≈ 131 yd
100 yd zero0.8 in low0.3 in low0.0 in3.5 in low—
200 yd zero0.4 in low0.6 in high1.8 in high0.0 in≈ 35 yd

Compare zeros for this load

25, 36, 50, 100 and 200 yd zeros side by side, so you can see which ones end up nearly the same.

Zero25 yd50 yd100 yd200 yd300 yd400 ydOther crossing
25 yd0.0 in1.4 in high3.4 in high3.3 in high2.8 in low15.4 in low≈ 263 yd (far)
36 yd0.5 in low0.5 in high1.5 in high0.5 in low8.4 in low22.9 in low≈ 186 yd (far)
50 yd0.7 in low0.0 in0.5 in high2.5 in low11.5 in low27.0 in low≈ 131 yd (far)
100 yd0.8 in low0.3 in low0.0 in3.5 in low13.0 in low29.0 in low—
200 yd0.4 in low0.6 in high1.8 in high0.0 in7.7 in low21.9 in low≈ 35 yd (near)

How to use it at the range

Set the zero distance you want and the distance you can actually shoot at. If your range is only 25 yards, the first result tells you where your group should land at 25 yards to be zeroed at 100. Adjust until it's there, then confirm at the real distance as soon as you can.

The bullet starts below your scope, rises through the line of sight at the near zero, and comes back down through it further out. That's why a 36 or 50 yard zero also gives you a second zero much further out. The comparison table shows how close each option ends up for your load.

How this calculator works

We run the same point-mass G1/G7 trajectory engine as the Atlas app. It finds the launch angle that makes the bullet cross your line of sight at your zero distance, then solves impact at every other range, including your sight-in distance. The other line-of-sight crossing (near or far zero) is interpolated between solved ranges.

Worked example: 6.5 Creedmoor, 140 gr at 2,710 fps, G7 0.315, 1.75 in sight height. For a 100 yd zero it should hit about 0.8 in low at 25 yd. A 36 yd zero is about 1.5 in high at 100 yd and crosses back down near 190 yd.

Note: Results assume a level shot in still air with exact inputs. Always confirm your zero on paper at the real distance.

Frequently asked questions

A 36 yard zero sights the rifle so the bullet crosses the line of sight at 36 yards on the way up. With typical rifle loads and a scope about 1.5–1.75 in above the bore, it rises a little above the line of sight and comes back down to a second zero, often somewhere around 180–300 yards. That keeps it within a few inches out to normal hunting or carbine distances. Your exact numbers depend on velocity, BC and sight height, which is why the calculator solves them for your load.

Pick 100 yards as the zero you want and 25 yards as your sight-in distance. The calculator shows where the bullet should hit at 25 yards (usually a little low because the scope sits above the bore). Adjust until your group lands there, then confirm at 100 yards. A short-range sight-in only gets you close, since small errors grow with distance.

Often close, but not always. A bullet that crosses the line of sight at 50 yards on the way up comes down through it again further out, often around 200 yards for typical rifle loads. Where that second crossing lands depends on velocity, BC and sight height. The comparison table shows both zeros side by side for your load.

Use 100 yards if you dial or hold using a ballistic solution, since most turret and reticle data assumes it. A 36, 50 or 200 yard zero suits shooters who want to hold center out to a moderate distance without adjusting. For a zero picked around your target size, use the MPBR calculator.

The calculator assumes your entered velocity, BC and sight height are exact, the shot is level and there is no wind. Measure sight height carefully and use a chronograph for velocity. Always confirm the zero on paper at the distance you want it.

More free ballistic calculators

All free, all in the browser, no download needed.