.277 Fury Twist Rate

Recommended twist
1:8.5"
Factory rates
1:7.5" · 1:8" · 1:8.5"
Bullet diameter
0.277"

For reference, a 135 grain bullet at 2830 fps in a 1:8.5" barrel comes out at a stability factor of 2.15.

.277 Fury twist rate chart

Required twist is the rate that puts each bullet at a stability factor of 1.5. The remaining columns show the stability factor you actually get in each barrel. Tap any row to load that bullet into the calculator below.

BulletNeedsSg 1:7.5"Sg 1:8"Sg 1:8.5"
135 gr FMJ1:10.2"2.762.432.15
140 gr hunting1:9.9"2.612.292.03
150 gr bonded1:9.5"2.392.101.86
165 gr ELD-X1:9.0"2.141.881.66

Green is properly stable (1.5 and above), amber is marginal, red will not stabilize. Figures are calculated with the Miller twist rule at standard sea-level conditions, the same way the mobile app does it. Velocity is listed for reference and is not part of the calculation. Lengths marked "est." are approximate for that bullet class; stability is very sensitive to length, so measure your own bullet and check it in the calculator above before relying on a marginal result.

Save your .277 Fury rifle and loads once in the free Atlas app, then check stability and get your holds at the range. It works offline.

Download the App

.277 Fury is the military 6.8x51 round, and unlike the old .270 Winchester it uses a fast 1:8.5" or quicker twist to stabilize modern high-BC .277 bullets from short barrels.

1:8.5" is the factory rate and works across the load range. Short 13 to 16 inch barrels lose velocity, which lowers stability, so faster is the safer side to err on.

Check your own .277 Fury load

Pre-filled with a typical .277 Fury bullet. Change the bullet dimensions or twist to match your rifle.

Bullet

Barrel

Conditions

Bullet length matters more than weight — measure it or take it from your load data rather than guessing.

Stability (Sg)
2.15

Matches the app’s stable classification at standard atmosphere.

Verdict
Stable

Twist recommendation

Twist needed for Sg 1.51:10.2"
Your twist1:8.5"
Sg at your conditions2.15
MarginFaster than required

Working figures

Bullet length4.48 calibers
Twist30.7 calibers / turn
Reference atmosphere59°F · 29.92 inHg

Take this solver to the range — works 100% offline

Save your rifles and loads once, pull live weather or pair a Kestrel, and get instant elevation and wind holds with zero cell service.

Download the App

Free on iPhone and Android. Your website inputs are not automatically imported into the app.

How twist rate works in .277 Fury

A bullet in flight is trying to tumble. Air pressure on the nose creates a force that wants to flip it end over end, and the only thing preventing that is the spin the rifling gave it. Twist rate sets how much spin the bullet leaves with, so it sets which bullets your barrel can actually stabilize.

Length is the driver, not weight. Long, sleek, high-BC bullets are harder to stabilize than short stubby ones of the same mass, which is why two bullets of identical weight can have very different twist requirements. The Miller rule used here accounts for that directly, which is why every figure on this page is calculated from bullet length rather than looked up from weight alone.

Aim for a stability factor of 1.5 or better rather than merely clearing 1.0. The figures here use the mobile engine’s standard-atmosphere Sg formula. In the app, actual stability is corrected for temperature and station pressure: colder, denser air reduces stability.

Twist rate for other cartridges

Recommended twist, the factory rates you will actually find, and a calculated stability chart for the bullets each cartridge shoots.

Barrel sorted? Next comes the trajectory — see the full .277 Fury ballistics chart.

Comparing shoulder kick across loads? See .277 Fury recoil in ft-lbs.

Want the raw calculator without a cartridge preset? Use the twist rate calculator.

Get the full solver in your pocket

Atlas Ballistics runs this same engine on your phone — with wind, spin drift, Coriolis, aerodynamic jump, truing from real shots, saved rifle and ammo profiles, and range cards that work offline.

Download the App

Free to start · No account required to calculate

Frequently asked questions

1:8.5" is the factory rate and works across the load range. Short 13 to 16 inch barrels lose velocity, which lowers stability, so faster is the safer side to err on. The figures on this page are calculated rather than looked up, so you can check any specific bullet in the calculator above.

The rates you will actually encounter are 1:7.5", 1:8", 1:8.5". 1:8.5" is the most common and the one to default to.

A 165 gr ELD-X needs roughly 1:9.0" to reach a standard-atmosphere stability factor of 1.5 using the mobile engine’s formula. Anything faster than that has margin; anything slower is cutting it fine, especially in cold, dense air.

Rarely. Extra spin adds a little spin drift and slightly amplifies any imbalance in the bullet, and very high velocity combined with very fast twist can stress thin jackets. For almost everyone, erring fast is the safer choice because it leaves room for heavier bullets later.

The mobile engine’s standard Sg formula uses bullet weight, diameter, length and barrel twist, not barrel length or muzzle velocity. This calculator follows that formula. Real-world performance still needs to be checked with your rifle and ammunition.

More free ballistic calculators

All free, all in the browser, no download needed.